How to read technical drawings
Contents |
[edit] Introduction
The term ‘technical drawing’ has a very broad meaning, referring to any drawing that conveys the way that something functions or how it is constructed. Most drawings prepared during the later stages of the design and construction of buildings might be considered to be technical drawings.
It is important that the purpose for which technical drawings are being prepared and the people that will use them are carefully considered to ensure they are properly structured and adopt an appropriate presentational techniques. It is also important to have an understanding of how to read them.
Some of the components common to many types of technical drawing are set out below.
[edit] Border
Most drawings have a border around them. This helps ensure that the full drawing is included in reproductions.
The border sometimes includes letters and numbers to delineate zones, in the same way as a map, to help locate and pinpoint certain areas. These letters are in alphabetical order from the bottom up on the vertical axis. The numbers are in numerical order from right to left on the horizontal access. The zones are to be read from right to left.
[edit] Title block
A title block will typically appear in the bottom-right corner of a drawing and contains information related to the drawing, including:
- Name: The company or agency that prepared the drawing.
- Address: Location of the company or agency.
- Names and dates: Individuals who drew, checked and approved the drawing, and the date they did so.
- Project: The project the drawing relates to.
- Description: What the drawing is of.
- Status: What the drawing is for (eg for construction / for information).
- Drawing number: The assigned number to identify the drawing.
- Revision: Identifies the correct version of the drawing, as it may have been revised several times.
- Scale: Ratio of actual size compared to the size on the drawing / or 'do not scale' if dimensions are not to be relied upon.
- Size: The original drawing sheet size (important for determining the scale for reproductions'. See paper sizes for more information.
[edit] Revision block
A separate revision block may be located in the top-right corner of the drawing, setting out:
- The number of the revision.
- The specific changes made compared to the previous drawings.
- The date that the revisions were made.
- The approval of the revision.
[edit] Scale
It is essential to understand the size scale that the drawing has been produced to. Actual size is 1:1. Where the scale is 100:1, it means that the actual size is 100 times that shown on the drawing; the first number represents the size of the physical element, and the second number represents the drawing. It is usual that the scale will be provided in the title block.
If the dimensions of elements on the drawing are not to be relied upon, for example if the drawing is a sketch, or if responsibility for determining dimensions are with another party, the scale may be followed by the statement 'do not scale' or 'not to scale'.
[edit] Basic symbols
Architectural symbols are often used to identify common features such as topography, brickwork, doors, windows, fixtures and other elements. Understanding these, or having access to a key which notates them, will be useful in terms of interpreting the drawing.
For more information, see Symbols on architectural drawings.
[edit] Notation and units
The same notation conventions should be followed by all so that there is clear communication between different people and mistakes are avoided.
See Notation and units on drawings and documents for more information.
[edit] Circled numbers
The scale of drawings may be too small to recreate all the necessary detail. In this case, circled numbers can be added to certain parts of the drawings, which indicate that the section identified is shown in greater detail on another page.
[edit] Projections and views
Drawings generally include front, side and top of views of the object being designed. These drawings are typically drawn in either parallel or perspective projections:
- Parallel projections include orthographic drawings in which the four orthogonal views of an object are shown.
- Perspective projections are drawings in which an object is drawn using one-, two- or three-point perspective; presenting the object as three-dimensional.
For more information, see Drawing projections.
Section views may also be included which show a structure as though it has been sliced in half or cut along another imaginary plane. For more information, see Section drawing.
Exploded views may also be shown, which show how an item is assembled. See Assembly drawing for more information.
[edit] Abbreviations
Similar to circled numbers, abbreviations are used to indicate elements and instructions. Some common abbreviations used in drawings include:
- & - and
- AFF - above finished floor
- BSMT - basement
- BYND - beyond
- BOT - bottom
- CLG - ceiling
- CONT - continuous
- CPT - carpet
- DBL - double
- DEMO - demolition
- DIA - diameter
- DIM - dimension
- DN - down
- DP - depth
- DR - door
- DWG - drawing
- EA - each
- EJ - expansion joint
- EL - elevation
- ELEC - electrical
- ELEV - elevator/elevation
- EXT - exterior
- FIXT - fixture
- FLR - floor
- FND - foundation
- GA - gauge
- HI - high
- HP - high point
- HVAC - heating, ventilating and air conditioning
- INSUL - insulation
- INT - interior
- LO - low
- MECH - mechanical
- MEMBR - membrane
- MTL - metal
- NO - number
- NOM - nominal
- OC - on centre
- PLUMB - plumbing
- PLYD - plywood
- PNT - paint/painted
- PVC - polyvinyl chloride
- REQD - required
- RM - room
- SIM - similar
- SPEC - specified
- STRUCT - structure
- TO - top of
- UNO - unless noted otherwise
- U/S - underside
- VIF - verify in field
- W/ - with
For more information see Acronyms.
[edit] Find out more
[edit] Related articles on Designing Buildings Wiki
- As-built drawings and record drawings.
- Assembly drawing.
- Component drawing.
- Computer aided design.
- Concept drawing.
- Detail drawing.
- Elevations.
- Engineering drawing.
- General arrangement drawing.
- How to take off construction works.
- Installation drawings.
- Notation and units on drawings and documents.
- Paper sizes.
- Production information.
- Projections.
- Section drawing.
- Symbols on architectural drawings.
- Types of drawing.
- Working drawing.
[edit] External references
- VistaIndustrial - How to read a drawing
Featured articles and news
From mud bricks to smart concrete
A brief history of building materials.
Building automation and control systems market study
BSRIA 2024 North America BACS software & services.
Impact of digital technology on productivity in construction
New CIOB academy guidance for companies of all sizes.
Demolition and retrofit approaches in Planning Policy
MHCLG survey informing potential government updates.
Expert taskforce to spearhead new, new town generation
Sir Michael Lyons given 12 months for recommendations.
Government policy statement on new towns
A coded vision for a new generation of new towns.
AT Principal Designer exemplars published
Supporting clear and comprehensive demonstration of the skills required.
Homes England goes to TOWN for co-housing project
Marmalade Lane developer selected for Northstowe neighbourhood.
Cohousing and related approaches to solve housing issues
Different forms of community housing explained with examples.
Alternative and off-grid housing communities in the UK
From Hockerton Housing Project to Tinkers Bubble.
Skills gap highlighted to Minister for Industry
Key opportunity in mission for economic growth and net-zero.
Specifying XPS in masonry cavity walls below DPC level
Moisture requirements, DPCs and third party certification.
Types of rigid foam insulation
A brief description and some of the main construction types.
Metal composite material panel systems MCM and MCP
Sandwich finishes, forms, details, core and their impacts.
Cumbria's vernacular architecture
A history of building impeded by unsettled times.
CIOB and MMC Ireland announce strategic partnership
For better working conditions, and a more productive construction sector.