Night-time purging
It can be necessary to provide cooling to buildings during warm weather, or where there are significant thermal gains, such as solar gain, people and equipment. This cooling is sometimes referred to as comfort cooling.
Thermal mass can be used to help cool buildings, or to reduce the need for active cooling systems such as heating, ventilation and air conditioning (HVAC) systems. Thermal mass describes the ability of a material to absorb, store and release heat energy. It can be used to store high thermal loads by absorbing heat during warm conditions, to be released when conditions are cooler. This can be beneficial both during the summer and the winter.
Night-time cooling, or night-time purging uses the thermal mass of a building to absorb heat gains during the day, then cools the mass at night using external air and discharging accumulated heat to the outside so the temperature of the thermal mass is lowered ready for the next day. In the UK this reduces internal temperature rises during the day by around 3 to 6°C.
Night-time cooling requires that the construction of the building includes significant thermal mass which is exposed both to the occupied spaces of the building and to ventilation paths (either directly, or by indirect convection). This can mean that buildings have exposed concrete floor slabs, exposed brick walls, no carpets, no suspended ceilings and so on. Thermal mass for night-time cooling is most efficient in horizontal surfaces, in particular floors, as cool ventilation air will tend to fall to the floor level. NB the exposed mass can cause acoustic issues with high internal reverberation.
Night-time cooling is particularly effective in climates with a large diurnal temperature range (an absolute minimum of 5°C), where external air temperatures are too high to provide adequate natural cooling during the day, but where night-time temperatures are low enough to ‘pre-cool’ the building ready for the next day. NB Diurnal temperature differences may be lower in urban environments than rural environments.
It is also best suited to buildings are occupied during the day, but unoccupied at night.
Night-time purging can be passive, active or hybrid:
- Passive systems rely on passive or natural ventilation to supply fresh outside air into the building and remove warm internal air, and in so doing, remove heat from the thermal mass. Natural ventilation can be wind driven or buoyancy driven. Buoyancy-driven stack ventilation can be particularly effective as a passive mechanism for night-time purging as this is generally the time of day when the difference between the internal and external temperature is at is greatest and so the stack effect is at its strongest. Passive systems have very low operational and maintenance costs. However, they require open air pathways within the building, which can be a security or privacy issue, and natural ventilation may not be possible because of local air quality or noise issues.
- Active systems use fan assistance to help drive air across the thermal mass, for example by ventilating floor voids. Active systems can be more targeted and controllable than natural systems, and air duct sizes can be smaller. Fan operation consumes energy, but this will tend to be less than full HVAC systems.
- Hybrid systems may only activate fan assistance when natural ventilation is insufficient.
The thermodynamics of night-time cooling is extremely complicated and requires careful analysis.
Correct operation may require staff training and fine tuning after occupation to ensure that the process is performing as expected. Careful control is required to ensure the correct level of cooling is provided. Building management systems (BMS) can use information about external and internal conditions to determine the level of cooling required and to activate systems.
NB it is important in the first instance that heat loads are minimised, for example by providing shading to reduce solar gain.
NB Approved document F, Ventilation, defines 'purge ventilation' as, ‘…manually controlled ventilation of rooms or spaces at a relatively high rate to rapidly dilute pollutants and/or water vapour. Purge ventilation may be provided by natural means (e.g. an openable window) or be mechanical means (e.g. a fan).
[edit] Related articles on Designing Buildings
Featured articles and news
About the 5 Percent Club and its members
The 5% Club; a dynamic movement of employers committed to building and developing the workforce.
New Homes in New Ways at the Building Centre
Accelerating the supply of new homes with MMC.
Quality Planning for Micro and Small to Medium Sized Enterprises
A CIOB Academy Technical Information sheet.
A briefing on fall protection systems for designers
A legal requirement and an ethical must.
CIOB Ireland launches manifesto for 2024 General Election
A vision for a sustainable, high-quality built environment that benefits all members of society.
Local leaders gain new powers to support local high streets
High Street Rental Auctions to be introduced from December.
Infrastructure sector posts second gain for October
With a boost for housebuilder and commercial developer contract awards.
Sustainable construction design teams survey
Shaping the Future of Sustainable Design: Your Voice Matters.
COP29; impacts of construction and updates
Amid criticism, open letters and calls for reform.
The properties of conservation rooflights
Things to consider when choosing the right product.
Adapting to meet changing needs.
London Build: A festival of construction
Co-located with the London Build Fire & Security Expo.
Tasked with locating groups of 10,000 homes with opportunity.
Delivering radical reform in the UK energy market
What are the benefits, barriers and underlying principles.
Information Management Initiative IMI
Building sector-transforming capabilities in emerging technologies.
Recent study of UK households reveals chilling home truths
Poor insulation, EPC knowledge and lack of understanding as to what retrofit might offer.