Blockwork
Contents |
[edit] Introduction
Blocks are constructed using concrete or cement. They may include a hollow core to make them lighter and to improve their insulation properties. They have been in use since the 1930s when they were commonly used for the inner leaf of cavity walls. At this point they were made from an aggregate of stone or industrial waste such as clinker or breeze, hence the term ‘breeze block’.
They are now used for a wide variety of purposes such as the construction of load-bearing walls, retaining walls, partitions and foundations.
A standard block is 440 mm x 215 mm, the equivalent of 3 bricks high and 2 long, the maximum size that one person can comfortably lift. They are available in a range of widths from 50 mm to 300 mm.
The kind of block selected for a particular application will depend on its:
- Density.
- Load-bearing characteristics.
- Appearance.
- Weight and handling properties.
- Thermal characteristics, such as U-value or thermal mass.
[edit] Dense blocks
Dense blocks are usually made from cement, fine aggregate and coarse aggregate. They can be produced in a range of crushing strengths and tend to be used for structural purposes, such as foundations and load-bearing walls.
They generally have poor thermal insulation and readily absorb water, but have good thermal mass.
[edit] Lightweight blocks
The advantage of lightweight blocks include their thermal insulation characteristics and ease of handling. During the last 80 years a variety of aggregates have been used - clinker blocks (8 parts clinker to 1 part cement), and blast furnace slag. They may be slightly more expensive than dense blocks
[edit] Aerated blocks
Aerated blocks are made from cement, lime, sand, pulverised fuel ash (from power stations). They are popular for a number of reasons, other than their light weight and good thermal insulation:
- Their closed cell structure means they have good resistance to water penetration.
- They provide good fire protection.
- They are easy to cut with a saw.
- They can accommodate fixings such as screws and nails.
Autoclaved aerated concrete (AAC) blocks are manufactured by adding a foaming agent to concrete and then hardening the blocks (autoclaving) with steam.
[edit] Mortar mixes
Mortar mixes should not be too strong. Mixes of cement : sand 1 : 3 are unsuitable because they will not accommodate movement in the blockwork.
For above ground uses, they might include mixes such as:
- cement : lime : sand 1 : 1 : 6
- cement : sand with plasticiser 1 : 6
- masonry cement : sand 1 : 5
- cement : lime : sand 1 : 2 : 9
Below ground a slightly stronger mortar can be used, such as 1 : 0.5 : 4 cement : lime : sand.
Dense blocks are typically laid in mortars of average strength, 1:1:6 or 1:2:9. Stronger mortars may limit movement and may cause cracking of the blocks, although they are sometimes specified below ground level.
[edit] Related articles on Designing Buildings
- Aircrete blocks.
- Ashlar.
- Brick.
- Bricklayer.
- Brick sizes.
- Coal ash.
- Ceramics.
- Concrete.
- Damp-proof course.
- Defects in brickwork.
- Defects in stonework.
- Dust heap.
- Hempcrete.
- How to lay block paving.
- How to lay bricks.
- Lime mortar.
- Mortar.
- Parge coat.
- Pebbledash.
- Perpend.
- Pyrite and mica redress issues in Dail Eireann.
- Quoin.
- Rendering.
- Rustication.
- Screed.
- Stucco.
- Timber.
- Types of brick.
- Types of brick bonding.
Featured articles and news
Infrastructure that connect the physical and digital domains.
Harnessing robotics and AI in challenging environments
The key to nuclear decommissioning and fusion engineering.
BSRIA announces Lisa Ashworth as new CEO
Tasked with furthering BSRIA’s impressive growth ambitions.
Public buildings get half a million energy efficiency boost
£557 million to switch to cleaner heating and save on energy.
CIOB launches pre-election manifesto
Outlining potential future policies for the next government.
Grenfell Tower Inquiry announcement
Phase 2 hearings come to a close and the final report due in September.
Progress from Parts L, F and O: A whitepaper, one year on.
A replicated study to understand the opinion of practitioners.
ECA announces new president 2024
Electrical engineer and business leader Stuart Smith.
A distinct type of countryside that should be celebrated.
Should Part O be extended to existing buildings?
EAC brands heatwave adaptation a missed opportunity.
Definition of Statutory in workplace and facilities management
Established by IWFM, BESA, CIBSE and BSRIA.
Tackling the transition from traditional heating systems
59% lack the necessary information and confidence to switch.
The general election and the construction industry
As PM, Rishi Sunak announces July 4 date for an election.
Eco apprenticeships continue help grow green workforce
A year after being recognised at the King's coronation.
Permitted development rights for agricultural buildings
The changes coming into effect as of May 21, 2024.