Screed
Contents |
[edit] Introduction
Generally, concrete floors, other than those in buildings such as warehouses which may be left exposed, are covered with a screed layer. This is a layer of material, usually a sand and cement mix (sometimes with added fibres and other additives), or a proprietary flowing screed. Screeds are generally laid to prepare for the installation of a floor covering, such as tiles, carpet or timber. Standards for screeds are set out in BS 8204, Screeds, bases and in-situ floorings.
The specification of screeds will vary depending on the requirement for:
- Load-bearing capacity.
- Durability.
- Creating a level surface.
- Providing a suitable base for flooring.
- Providing a suitable wearing surface.
[edit] Types of screed
The most common types of screed include:
[edit] Bonded screed
The screed layer is fully bonded to the substrate using a primer or bonding agent. This method is commonly used for thinner screeds where heavy loading is expected and where there is not enough space available to lay an unbonded screed. The optimum thickness of a sand and cement bonded screed is generally in the region of 25-40 mm. Some calcium sulphate flowing screeds can be laid at a minimum depth of 12 mm. Care must be taken during the laying process to ensure de-bonding does not occur as this can lead to instability and ultimately, the screed may fail.
[edit] Unbonded screed
Instead of being bonded directly to the base, unbonded screeds are applied over a damp proof membrane (DPM) laid on top of the concrete base. The minimum thickness of an unbonded sand and cement screed is usually in the region of 50 mm. Calcium Sulphate screeds can be laid unbonded at a minimum depth of 30 mm. The advantage of an unbonded screed is that the flooring is not in direct contact with the main structure and so the potential impacts of settlement or shrinkage can be less problematic. The DPM creates a barrier preventing damp rising from the substrate.
However, this type of screed can be more prone to curling if dried quickly. Curling is a vertical distortion of the edges due to temperature differences or moisture content throughout the thickness of the screed. This can be prevented by adhering to minimum specified thicknesses and allowing for slow drying. Calcium Sulphate screeds are not prone to curling due to their lower rates of shrinkage compared to sand and cement screeds.
[edit] Floating screed
The screed is laid on top of insulation to create a thermally efficient floor. Floating screeds are commonly used where underfloor heating systems are provided or thermal or acoustic insulation is required. Floating sand and cement screeds generally have a thickness greater than 65 mm for lightly-loaded floors and 75 mm for more heavily-loaded floors. Calcium Sulphate floating screeds can be installed at 35 mm depth for domestic use or 40 mm for commercial use.
[edit] Flow/liquid Screed
Liquid flow screed is fast becoming the industry standard in floor screeds. This type of floor is also referred to as self compacting screed or a calcium sulphate screed. Simple in its preparation this new form of flow screed is suitable for light foot traffic in 24-48 hours. Partitions can be installed and/or the screed can be loaded out 7 days after installation.
[edit] Screed over underfloor heating
This is where the floating screed layer is installed over underfloor heating pipes or insulation. The screed serves to conduct the heat evenly across the floor surface, avoiding hot or cold spots, and helps to retain heat for longer. In order that heat propagates only in the required direction of the room to be heated or cooled, the elements are inserted above insulating panels. Sand cement screeds require a minimum thickness of 65 mm, with the ideal being between 65-75 mm.
Where fibres are added or when using anhydrite screeds the minimum thickness may be reduced to 50 mm. Some specialised calcium sulphate screeds can be installed with only 20 mm cover to the heating pipes, giving screed depths of less than 40 mm.
Care must be exercised in allowing adequate drying time (usually around 21 days) before incrementally turning on the heating system, otherwise cracking may occur. Additives can be included in the screed mix to allow the drying time to be reduced. Calcium sulphate screeds can be force dried, using the underfloor heating, after 7 days.
All types of screed should have the underfloor heating run through a heating/cooling cycle before floor coverings of any type are installed.
[edit] Composition of screed
Most screeds are made from a 1:3 to 1:4.5 ratio of cement to sand. Enhanced screeds include additives to improve the properties of the standard screed. This can allow for faster drying times and extra strength if required.
Manufacturers also offer self-compacting screeds that can be pumped through a delivery hose and levelled with a dappling bar. The majority of these screeds are anhydrite compounds based on a calcium sulphate binder. Large areas can be covered more quickly, however, care must be taken to ensure this type of screed dries completely. Calcium sulphate screeds cannot be laid to a fall and are not suitable for permanently wet areas such as wet rooms, saunas, steam rooms and swimming pool surrounds.
All screeds expand and contract to some degree so large areas need to have expansion joints or crack inducer cuts in the screed to allow movement without cracking.
[edit] Related articles on Designing Buildings Wiki
- Aggregate.
- Cement.
- Concrete.
- Floor definition.
- Floor screed costs.
- Flooring.
- Insulation.
- Laser screed.
- Portland cement.
- Power float.
- Raised floor.
- Reinforced concrete.
- Rendering.
- Wet trades.
[edit] External references
Featured articles and news
Download your free guide.
Four new types of prior approval for solar developments
Online Planning Portal application types from 5 September.
Election fails to spark construction industry revival
Contract awards and planning; post election.
Making diversity and inclusion easy for SMEs
The CIOB tool for companies with limited resources.
Sustainable Futures: Redefining Retrofit for Net Zero Living
BSRIA Briefing 2024, initial speakers announced.
Looking back at the UK's first Passivhaus leisure centre
Reflections on St Sidwell’s Point with CIAT.
A-Level results and electrical apprenticeships
Electrical Skills Index highlights areas with skills shortages.
One of the world's more unusual drive-throughs.
A quick introduction.
Hadrian's Wall Path and the national trails
The trails are heritage assets in their own right.
Articles on timely advice and hydraulic lime.
Building Designers Association of Australia
CIAT and BDAA sign Memorandum of Understanding.
Built Environment Inclusive partners issue statement committed to inclusion.
Building regulation requirements can have unintended consequences.
CIOB announces 2024/25 vice president
Sustainability champion Professor Saul Humphrey.
Accelerating towards a net-zero built environment.
Comments
Not all flowable screeds are Calcium Sulphate . Many are based on cement with the use of a copolymer which produces a strong, hardwearing surface similar to concrete.
Cementitious screeds based on advanced technology are also now available that incorporate all of the benefits of a semi-dry screed such as laying to falls or creating steps in doorways to accommodate different floor finishes whilst also incorporating many of the benefits of flow applied screeds. Retanol Xtreme that is BREEAM and TÜV Rheinland certified (zero harmful content) requires no curing under polythene, dries to under 75%RH in 3-4 days, can be laid from 15mm thick bonded and 35mm thick floating, is suitable for wet or dry, internal or external conditions. It dries uniformly throughout the body of the screed rather than from the top down so no cracking or curling and no requirement for fibre reinforcement. It is also ideal for UFH systems as it can be applied at just 30mm cover and commissioning can take place after just 24 hours with a 60% improvement in conductivity over traditional screed systems. Heavy Duty versions are available but even the standard version achieves compressive strengths of up to 50N/mm².