Plaster
Contents |
[edit] Introduction
Plaster is a building material used for coating, protecting and decorating internal walls and ceilings. It can also be used to create architectural mouldings such as ceiling roses, cornices, corbels, and so on.
The most common types of plaster are a composition of gypsum, lime or cement with water and sand. The plaster is typically manufactured as a dry powder and then worked to form a stiff paste by mixing in water before application.
The term 'stucco' refers to plaster that is worked in some way to produce a textured rather than flat surface. See Stucco for more information.
Render is similar to plaster, but is applied to the outside of buildings and has waterproofing properties. See Rendering for more information.
[edit] History of plastering
A form of plastering was used by primitive civilisations, creating durable and weather-resistant structures using mud. The Egyptian pyramids contain plasterwork comparable to that used today that remains hard and durable some 4,000 years later.
Greek artisans used plaster, mainly to cover the exterior of temples but sometimes also interiors. Through history, plaster ceilings became increasingly ornamental, with those during the Tudor period being particularly extravagant.
However, the use of plaster as a means of demonstrating artistic skill and expression had waned by the 19th century, when imitation and mechanical reproduction displaced it as a creative medium. However, plaster is still very commonly used as a surface finish for interior walls, ceilings, and still sometimes for exterior walls.
[edit] Types of plaster by binder
There are a number of different types of plaster, depending on the binder that is used.
[edit] Gypsum plaster
Gypsum plaster, or ‘plaster of Paris’ (POP), is the most common form of plaster for interior walls. It is produced by heating gypsum to around 150°C (300 °F). When mixed with water, the dry plaster powder re-forms into gypsum. Unmodified plaster starts to set about 10 minutes after mixing, but it will not be fully set until 72 hours have elapsed. Gypsum plaster has good fire-resistant qualities.
[edit] Lime plaster
Lime plaster is a composite of calcium hydroxide (lime) and sand (or other inert fillers). It may sometimes be strengthened with animal hair to preventing cracking and reduce shrinkage. The plaster sets through contact with carbon dioxide in the atmosphere which transforms the calcium hydroxide into calcium carbonate (limestone). It is typically more flexible and breathable than gypsum and cement plasters, and is most commonly used on older properties.
[edit] Cement plaster
Cement plaster is a mixture of sand, cement and water. It is normally applied to masonry interiors and exteriors. While it is capable of achieving a smooth surface, interiors will sometimes require an additional finishing layer of gypsum plaster. Cement plaster offers greater moisture resistance than gypsum plaster.
[edit] Clay plaster
Clay plaster is considered to be a more sustainable alternative to modern plasters, with a lower embodied energy than gypsum, cement or lime based plasters. It is available with fibre additives to increase its strength, and in a range of ‘natural’ colours. It is breathable and does not need to be painted.
[edit] Types of plaster by application
Plasters can also be categorised by application:
- Board finish plaster is used on plasterboard.
- Bonding plaster is used as an undercoat, applied to new walls.
- Browning plaster is used as an undercoat for particularly absorbent surfaces.
- Dri-coat plaster offers moisture resistance for walls that have had a damp proof course (DPC) inserted or injected.
- Hardwall plaster is similar to browning plaster, but is faster drying and has better impact resistance.
- Heat resistant plaster is used for walls and chimney breasts where temperatures may exceed 50°C.
- Multi-finish plaster is a top coat plaster.
- One-coat plaster is typically used as a patching plaster.
- Tough coat plaster has exceptional impact resistance.
[edit] Plastering techniques
Plaster is typically built up in layers, with the number of layers depending on the roughness of the surface being plastered. Rough, bare walls could require three coats of plaster, while plasterboard might just require a finishing skim of 2 to 3mm.
The plaster compound, which is typically supplied dry, must first be mixed with water, with care being taken to achieve the correct creamy consistency. Mixing is best achieved by adding the plaster to the water, not the other way round.
The plaster can then be applied to the wall. The first coat is applied, scratched and left to dry. This is followed by the second coat and finally a third finishing layer.
Plastering is a labour intensive and time-consuming process and as a result it has gone into something of a decline in recent years, with techniques such as dry lining gaining in popularity.
While plaster is durable, it can be prone to cracking if the building experiences settlement or if it has been applied incorrectly.
[edit] Plastering terminology
- Background.
- Blistering.
- Cracking.
- Crazing.
- Dubbing coat.
- Gauging.
[edit] Related articles on Designing Buildings
- Boss plaster.
- Caulk.
- Cement.
- Cement mortar.
- Clay plaster.
- Daub.
- Decorative metal ceilings.
- Dry lining.
- Drywall.
- Finishes.
- Fresco.
- Grout.
- Gypsum.
- Inspecting historic fibrous plaster ceilings.
- Lath and plaster.
- Lime plaster.
- Making Magnificence: architects, stuccatori and the eighteenth-century interior.
- Mortar.
- Rendering.
- Stucco.
- Tanking.
- Tiles.
- Wet trades.
Featured articles and news
Industry survey highlights persistent skills gap
Building engineering business survey by ECA in partnership with BESA, SELECT and SNIPEF.
IHBC Conservation Professional Practice Principles
Spotlighted in HEF Historic Environment Overview.
CIAT collaborates with CIOB, CIfA, Icon to launch The Arc
Helping clients find specialist historic environment professionals.
Government building safety remediation data releases
Show some progress, but a 50% gap not yet started.
Testing For A Safer Future; an initial industry response
A response to the Independent Review of the Construction Product Testing Regime.
Requirements for UK buildings in certain circumstances.
CLC guidance for dutyholders and accountable persons.
Types of contractor in the construction industry
A long list, but are any missing ?
The Housing (Cladding Remediation) (Scotland) Bill 2023
Unanimously approved to legislation on May 14, 2024.
Asset information requirements AIR
In detail, with links to further resources.
Where it's AT Building Safety podcasts from CIAT
Unravelling the Golden Thread and CIAT’s Principal Designer Register for non-HRBs and HRBs.
What happened to Hadrian's Wall?
Its former stones can be found in buildings near its route.
Strategic ventilation in modern building design
Download your free guide.
Four new types of prior approval for solar developments
Online Planning Portal application types from 5 September.
Comments