Pulley
This photograph shows a rope and pulley (or block and tackle) system. |
Contents |
[edit] Introduction
A pulley is a type of wheel system is used with an axle to support the movement of some type of load.
[edit] History
The earliest recorded existence of pulley systems appeared in Ancient Egypt, Mesopotamia and Greece where block and tackle configurations were commonly used to move heavy objects.
During the Renaissance, this system was included by scientists in their list of six simple machines. According to Galileo Galilei, the simple machines “do not create energy, only transform it.” In addition to the pulley, these machines included:
- Lever
- Wheel and axle
- Inclined plane
- Wedge
- Screw
The six simple machines often served as the basis for more complex machines.
[edit] Types of pulleys
There are several types of pulley:
- Fixed. A fixed pulley has an axle mounted in bearings attached to a supporting structure.
- Movable. A movable pulley is made up of an axle in a movable block. A single movable pulley can lift more than a single fixed pulley.
- Compound. This combination of fixed and movable pulleys is also known as rope and pulley or block and tackle. When a fixed pulley is combined with a movable pulley or another fixed pulley, it can achieve more ambitious mechanical goals.
[edit] Rope and pulley
When used in combination with a frame or shell (sometimes referred to as a block), the freely rotating movable pulley (or set of pulleys) may be referred to as a sheave. The pulley or sheave may have indentations or grooves around its circumference to accommodate a drive element (sometimes referred to as a tackle) in the form of a continuous cable, belt, rope or chain. The tackle transmits tension to move a load.
This combination of rope and pulley can be part of a simple system that is used to lift items or change the direction of their motion. With the aid of a block and tackle system, it is possible to lift heavy loads by the application of a relatively small amount of force.
There are different types of rope and pulley configurations. The variations are based on the tackle configuration. Increasing the number of pulleys and falls of tackle increases the load that can be moved. Pulleys can be incorporated into common items such as curtains and sliding doors or lifting equipment such as fire ladders or power–driven industrial trucks and so on.
[edit] LOLER and rope and pulley systems
The Lifting Operations and Lifting Equipment Regulations (LOLER) place legal duties and responsibilities on those who own, operate or have control over lifting equipment. Rope and pulley systems are one type of lifting equipment covered by the regulations.
LOLER was created under the Health and Safety at Work etc. Act 1974, and came into force in 1998, replacing several preceding pieces of legislation which had previously regulated the use of lifting equipment. LOLER defines lifting equipment as ‘work equipment for lifting or lowering loads and includes its attachments used for anchoring, fixing or supporting it.’
The regulations require:
- That lifting equipment is strong and stable enough for safe use.
- Equipment is marked to indicate safe working loads.
- Equipment is positioned and installed so as to minimise risks.
- A competent person plans, organises and performs the safe use of the equipment.
- Equipment is subject to ongoing thorough examination and inspection.
LOLER may not apply where a lift is not used by people at work (such as a lift in a shop used by customers). However, Section 3 of the Health and Safety at Work Act imposes general responsibilities for the safety of users.
LOLER requires that lifts are thoroughly examined by a competent person at least every six months or, in the case of goods-only lifts, every 12 months. Insurance companies will generally request that a third party independent inspector carries out the inspections. The minimum requirements are:
- Every six months for lifting equipment used for lifting/lowering persons.
- Every six months for lifting accessories.
- Every 12 months for all other lifting equipment not falling into either of the categories above.
[edit] Belt and pulley
Another use of the pulley is the belt and pulley system. This system uses a pulley in conjunction with a belt drive to direct power from one place to another. The belt and pulley system can also control the speed of the motion.
This photograph shows a belt and pulley system. |
This configuration consists of two or more pulleys used in conjunction with a belt. The necessary contact pressure between the belt and pulleys is ensured by appropriate tightening of the belt. This may be achieved by means of a tensioning roller or another pulley.
[edit] Related articles on Designing Buildings Wiki
Featured articles and news
Cladding remediation programmes, transparency and target date.
National Audit Office issue report on cladding remediation.
HBPT and BEAMS Jubilees. Book review.
Does the first Labour budget deliver for the built environment?
What does the UK Budget mean for electrical contractors?
Mixed response as business pays, are there silver linings?
A brownfield housing boost for Liverpool
A 56 million investment from Homes England now approved.
Fostering a future-ready workforce through collaboration
Collaborative Futures: Competence, Capability and Capacity, published and available for download.
Considerate Constructors Scheme acquires Building A Safer Future
Acquisition defines a new era for safety in construction.
AT Awards evening 2024; the winners and finalists
Recognising professionals with outstanding achievements.
Reactions to the Autumn Budget announcement
And key elements of the quoted budget to rebuild Britain.
Chancellor of the Exchequer delivers Budget
Repairing, fixing, rebuilding, protecting and strengthening.
Expectation management in building design
Interest, management, occupant satisfaction and the performance gap.
Connecting conservation research and practice with IHBC
State of the art heritage research & practice and guidance.
Innovative Silica Safety Toolkit
Receives funding boost in memory of construction visionary.
Gentle density and the current context of planning changes
How should designers deliver it now as it appears in NPPF.
Sustainable Futures. Redefining Retrofit for Net Zero Living
More speakers confirmed for BSRIA Briefing 2024.
Making the most of urban land: Brownfield Passports
Policy paper in brief with industry responses welcomed.
The boundaries and networks of the Magonsæte.